Quantcast

Troubleshooting Directly Connected Serial Interfaces

Get the WebProNews Newsletter:


[ Business]

CCNA exam success depends largely on noticing the details, and this is especially true of configurations involving directly connected serial interfaces.

And of course, it\s not enough to notice these details – you\ve got to know what to do about them!

A Cisco router is a DTE by default, but directly connecting two DTEs with a DCE/DTE cable is not enough. In the following example, R1 and R3 are directly connected at their Serial1 interfaces. The line goes up briefly after being opened, but the line protocol goes down after about 30 seconds.

R3(config-if)#int s1

R3(config-if)#ip address 172.12.13.3 255.255.255.0

R3(config-if)#no shutdown

2d18h: %LINK-3-UPDOWN: Interface Serial1, changed state to up

2d18h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up

R3(config-if)#

2d18h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down

The problem is that one of the routers needs to act as the DCE in order for the line protocol to come up and stay up. If this were your CCNA / CCNP home lab, you could just go over and look at the DTE/DCE cable to see which router had the DCE end of the cable attached. In this example, though, we don\t have physical access to the routers. How can we tell which router has the DCE end of the cable attached?

R3#show controller serial 1

HD unit 1, idb = 0x1C44E8, driver structure at 0x1CBAC8

buffer size 1524 HD unit 1, V.35 DCE cable

The show controller command gives us this information. (There\s a lot more output that this with this command, but it\s unimportant for our purposes.) The router with the DCE end of the cable needs to supply a clock rate to the DTE, and we\ll do just that with the interface-level clockrate command.

R3#conf t

Enter configuration commands, one per line. End with CNTL/Z.

R3(config)#int serial1

R3(config-if)#clockrate 56000

2d18h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up

In just a few seconds, the line protocol goes up and stays up.

When troubleshooting a connection, always run show interface first. If you see the combination shown below, the connection is physically fine but logically down. That\s generally the result of a needed keepalive not being present. With Frame Relay, it\s probably an LMI issue, but with directly connected serial interfaces the issue is most likely the DCE end of the connection not supplying clockrate.

R3#show interface serial 1

Serial1 is up, line protocol is down

Troubleshooting is a big part of the job, and it\s a big part of the Cisco CCNA and CCNP programs as well. Know your show and debug commands and you\re on your way to passing the CCNA!

Add to Del.icio.us | DiggThis | Yahoo! My Web | Furl

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of FREE CCNA and CCNP tutorials and daily exam questions, as well as The Ultimate CCNA and CCNP Study Packages.

For a FREE copy of his latest e-books, “How To Pass The CCNA” or “How To Pass The CCNP”, and for free daily exam question, visit the website and download your copies!

Troubleshooting Directly Connected Serial Interfaces
Comments Off
About Chris Bryant
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of FREE CCNA and CCNP tutorials and daily exam questions, as well as The Ultimate CCNA and CCNP Study Packages.

For a FREE copy of his latest e-books, "How To Pass The CCNA" or "How To Pass The CCNP", and for free daily exam question, visit the website and download your copies! WebProNews Writer
Top Rated White Papers and Resources

Comments are closed.

  • Join for Access to Our Exclusive Web Tools
  • Sidebar Top
  • Sidebar Middle
  • Sign Up For The Free Newsletter
  • Sidebar Bottom