If youre new to IPv6, youll quickly learn that its not exactly just two more octets slapped onto an IPv4 address! IPv6 addresses are quite long, but there are two ways to acceptably shorten IPv6 address expression. To pass the BSCI exam, become a CCNP, and get that all-important understanding of IPv6, youve got to understand these different methods of expressing an IPv6 address. My last IPv6 tutorial discussed zero compression; today well take a look at leading zero compression.

Leading zero compression allows us to drop the leading zeroes from every field in the address. Where we could only use zero compression once in an IPv6 address expression, leading zero compression can be used as often as is appropriate. The key with leading zero compression is that there must be at least one number left in each field, even if that remaining number is a zero.

You sometimes see books or websites refer to leading zero compression as “dropping zeroes and replacing them with a colon”, but that explanation can be a little confusing, since the blocks are separated with a colon to begin with. Youre not really replacing the leading zeroes, youre dropping them.

Lets look at an example of leading zero compression. Taking the address 1234:0000:1234:0000:1234:0000:1234:0123, we have four different fields that have leading zeroes. The address could be written out as it is, or drop the leading zeroes.

Original format: 1234:0000:1234:0000:1234:0000:0123:1234

With leading zero compression: 1234:0:1234:0:1234:0:123:1234

Theres no problem with using zero compression and leading zero compression in the same address, as shown here:

Original format: 1111:0000:0000:1234:0011:0022:0033:0044

With zero and leading zero compression: 1111::1234:11:22:33:44

Zero compression uses the double-colon to replace the second and third block of numbers, which were all zeroes; leading zero compression replaced the “00″ at the beginning of each of the last four blocks. Just be careful and take your time with both zero compression and leading zero compression and youll do well on the exam and in the real world. The keys to success here are remembering that you can only use zero compression once in a single address, and that while leading zero compression can be used as often as needed, at least one number must remain in each field, even if that number is a zero.

Tag:

Add to Del.icio.us | Digg | Reddit | Furl

Bookmark WebProNews:

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of FREE CCNA and CCNP tutorials and daily exam questions, as well as The Ultimate CCNA and CCNP Study Packages.

For a FREE copy of his latest e-books, “How To Pass The CCNA” or “How To Pass The CCNP”, and for free daily exam question, visit the website and download your copies!

To pass the BSCI exam and earn your CCNP, youll need to know these differences! Today, well take a look at ISIS Hello types and the adjacency types that form through the use of these Hellos.

Hello packets have been mentioned several times with ISIS, and with good reason. Hello packets are the heartbeat of OSPF and ISIS when heartbeats are no longer heard from a neighbor, that adjacency will be dropped. A major difference between OSPF and ISIS is that OSPF has one type of Hello packet, where ISIS actually has three!

An ES Hello (ESH) is send by all End Systems, and all IS devices listen for this Hello. This is how a router (IS) discovers a host (ES).

An IS Hello (ISH) announces the presence of an IS. An IS Hello is sent by all IS devices, and End Systems listen for these hellos.

An IS-to-IS Hello (IIH) is used by an IS to discover other ISes and to form adjacencies with them.

An interesting side note: A router will send an IIH to another router on the link to form or maintain an adjacency, but it will still send an ISH as well in case there are end systems located on that segment.

ISIS and OSPF both create and maintain adjacencies with the Hello packet. Lets take a look at the rules regarding ISIS adjacencies as well as the adjacency types.

L1 and L2 Hellos are different messages, so an L1 router must exchange Hellos with another L1 router to form an adjacency, just as L2 routers form adjacencies with L2 routers. L1 routers can only form an adjacency with an L2 router if one of the two routers involved is actually an L1/L2 router.

L1 routers must be in the same area in order to form an adjacency. The Hello timers, as well as the MTU, must match between the interfaces used to form the adjacency.

Thats a lot of L1, L2, and L1/L2, isnt it? Lets review the adjacencies each router type can form:

L1: Can form adjacency with any L1 in the same area and any L1/L2 in the same area.

L2: Can form adjacency with any L2 in any area, and with an L1/L2 in any area.

L1/L2: Can form adjacency with any L1 in the same area, L1/L2 in any area, and L2 in any area.

Knowing the similarities and differences regarding ISIS and OSPF is vital for CCNP exam success. Take your time, master the fundamentals, and before long the magic letters “CCNP” are behind your name and on your resume!

Tag:

Add to Del.icio.us | Digg | Yahoo! My Web | Furl

Bookmark WebProNews:

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of FREE CCNA and CCNP tutorials and daily exam questions, as well as The Ultimate CCNA and CCNP Study Packages.

For a FREE copy of his latest e-books, “How To Pass The CCNA” or “How To Pass The CCNP”, and for free daily exam question, visit the website and download your copies!

BGP is an external routing protocol used primarily by Internet Service Providers (ISPs). Unless you work for an ISP today or in the future, you may have little or no prior exposure to BGP. Understanding BGP is a great addition to your skill set – and you have to know the basics well to pass the BSCI exam.

Note that I said “the basics”. BGP is a very complex protocol, and when you pursue your CCIE, you’ll see what I’m talking about. As with all things Cisco, though, when broken down into smaller pieces, BGP becomes quite understandable. You will need to know the basics of BGP as presented in this chapter to pass your BSCI exam – so let’s get started.

BGP Defined:

“An Internet protocol that enables groups of routers (called autonomous systems) to share routing information so that efficient, loop-free routes can be established. BGP is commonly used within and between Internet Service Providers (ISPs).”

There are a couple of terms in there that apply to the protocols you’ve mastered so far in your studies. The term “autonomous system” applies to IGRP and EIGRP as well as BGP; you’ll be indicating a BGP AS in your configurations just as you did with IGRP and EIGRP. And we’re always looking for efficient, loop-free routes, right? As it did with IGRP and EIGRP, “autonomous system” simply refers to a group of routers that is managed by a single administrative body. An autonomous system will use an Interior Gateway Protocol (IGP) such as OSPF or EIGRP to route packets inside the AS; outside the AS, an Exterior Gateway Protocol (EGP) such as BGP will be used.

BGP shares some characteristics with some routing protocols you’ve already studied. BGP supports VLSM, summarization, and CIDR. Like EIGRP, BGP will send full updates when two routers initially become neighbors and will send only partial updates after that. BGP does create and maintain neighbor relationships before exchanging routes, and keepalives are sent to keep this relationship alive.

BGP has some major differences from the IGPs we’ve studied to this point. You’ll hear BGP referred to as a path-vector protocol. As opposed to distance-vector protocols that exchange relatively simple information about available routes, BGP routers will exchange extensive information about networks to allow the routers to make more intelligent routing decisions. This additional BGP path information comes in the form of attributes, and these path attributes are contained in the updates sent by BGP routers. Attributes themselves are broken up into two classes, well-known and optional.

BGP also keeps a routing table separate from the IP routing table.

Well take a look at BGP attributes in future BSCI tutorials. In the meantime, keep studying!

Tag:

Add to Del.icio.us | Digg | Yahoo! My Web | Furl

Bookmark WebProNews:

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of FREE CCNA and CCNP tutorials and daily exam questions, as well as The Ultimate CCNA and CCNP Study Packages.

For a FREE copy of his latest e-books, “How To Pass The CCNA” or “How To Pass The CCNP”, and for free daily exam question, visit the website and download your copies!

A quick check in a search engine for “troubleshoot SIA” will bring up quite a few matches. Troubleshooting SIA routes is very challengin in that theres no one reason they occur.

View the EIGRP topology table with the show ip eigrp topology command, and youll see a code next to every successor and feasible successor. A popular misconception is that we want these routes to have an “A” next to them – so theyre active. Thats what we want, right? Active routes sound good, right?

Well, they sound good, but theyre not. If a route shows as Active in the EIGRP topology table, that means that DUAL is currently calculating that route, and its currently unusable. When a route is Passive (“P), that means its not being recalculated and its a usable route.

Generally, a route shown as Active is going to be there for a very short period of time by the time you repeat the command, hopefully that Active route has gone Passive. Sometimes that doesnt happen, though, and the route becomes SIA – Stuck In Active.

A route becomes SIA when a query goes unanswered for so long that the neighbor relationship is reset. From experience, I can tell you that troubleshooting SIA routes is more of an art form than a science, but there are four main reasons a route becomes SIA:

The link is unidirectional, so the query cant possibly be answered.

The queried routers resources are unavailable, generally due to high CPU utilization.

The queried routers memory is corrupt or otherwise unable to allow the router to answer the query.

The link between the two routers is of low quality, allowing just enough packets through to keep the neighbor relationship intact, but not good enough to allow the replies through.

To sum it up, routes generally become SIA when a neighbor either doesnt answer a query, or either the query or reply took a wrong turn somewhere. I told you it wasnt the easiest thing to troubleshoot!

Add to Del.icio.us | DiggThis | Yahoo! My Web | Furl

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of FREE CCNA and CCNP tutorials and daily exam questions, as well as The Ultimate CCNA and CCNP Study Packages.

For a FREE copy of his latest e-books, “How To Pass The CCNA” or “How To Pass The CCNP”, and for free daily exam question, visit the website and download your copies!

With this in mind, heres a quick review of some details you should know for success in the exam room and real-world networks!

When packets need to be routed, the routing table is parsed for the longest prefix match if multiple paths exist with the same prefix length, the route with the lowest AD is preferred. If there are still multiple valid paths, equal-cost load-sharing goes into effect.

The ip route command is used to create static routes the command ip route 0.0.0.0 0.0.0.0 < next-hop-IP or local exit interface> creates a default static route.

A static route with a next-hop IP address has an AD of one, while a static route with a local exit interface has an AD of zero.

A floating static route is a static route with an AD higher than that of the dynamic routing protocols running on the router, ensuring that the static route can only be used if the routing protocol goes down.

On-Demand Routing (ODR) is only appropriate in a hub-and-spoke network. The spokes effectively become stub routers. ODR uses Cisco Discovery Protocol (CDP) to send route information.

To propagate a default route with IP routing, use the ip default-network command. To do so with IP routing disabled, use ip default-gateway. You can also redistribute a static route into most protocols, but not IGRP. IGRP does not understand a static route to 0.0.0.0.

The ip helper-address command takes certain broadcasts and translates then into unicasts in order to allow the router to forward them. These default ports are:

TIME, port 37

NetBIOS datagram services, port 138

To name other ports, use the ip forward-protocol command. To remove any of these ports from the default list, use the no ip forward-protocol command.

ICMP Router Discovery Protocol (IRDP) hosts hear multicast Hellos from routers, allowing host-router discovery. HSRP routers create a virtual router that hosts think is a real router. Both protocols help networks cut over to a functional router quickly when their primary router goes down.

Add to | DiggThis | Yahoo! My Web

Technorati:

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of FREE CCNA and CCNP tutorials and daily exam questions, as well as The Ultimate CCNA and CCNP Study Packages.

For a FREE copy of his latest e-books, “How To Pass The CCNA” or “How To Pass The CCNP”, and for free daily exam question, visit the website and download your copies!

Route summarization is just one of the many skills youll have to master in order to earn your CCNP. Whether its RIP version 2, OSPF, or EIGRP, the BSCI exam will demand that you can flawlessly configure route summarization.

Route summarization isnt just important for the BSCI exam. Its a valuable skill to have in the real world as well. Correctly summarizing routes can lead to smaller routing tables that are still able to route packets accurately – what I like to call “concise and complete” routing tables.

The first skill youve got to have in order to work with route summarization is binary math more specifically, you must be able to take multiple routes and come up with both a summary route and mask to advertise to downstream routers. Given the networks 100.16.0.0 /16, 100.17.0.0 /16, 100.18.0.0 /16, and 100.19.0.0 /16, could you quickly come up with both the summary address and mask? All you need to do is break the four network numbers down into binary strings. We know the last two octets will all convert to the binary string 00000000, so in this article well only illustrate how to convert the first and second octet from decimal to binary.

100 16 = 01100100 00010000

100 19 = 01100100 00010011

To come up with the summary route, just work from left to right and draw a line where the four networks no longer have a bit in common. For these four networks, that point comes between the 14th and 15th bits. This leaves us with this string: 01100100 000100xx. All you need to do is convert that string back to decimal, which gives us 100 for the first octet and 16 for the second. (The two x values are bits on the right side of the line, which arent used in calculating the summary route.) Since we know that zero is the value for the last two octets, the resulting summary network number is 100.16.0.0.

But were not done! We now have to come up with the summary mask to advertise along with the summary route. To arrive at the summary route, write out a mask in binary with a “1″ for every bit to the left of the line we drew previously, and a “0″ for every bit to the right. That gives us the following string:

11111111 11111100 00000000 00000000

Converting that to dotted decimal, we arrive at the summary mask 255.252.0.0. The correct summary network and mask to advertise are 100.16.0.0 252.0.0.0.

For the BSCI exam, emphasis is put on knowing how to advertise these summary routes in RIPv2, EIGRP, and OSPF. For RIP v2 and EIGRP, route summarization happens at the interface level – it’s not configured under the protocol. On the interface that should advertise the summary route, use the command “ip summary-address”. Here are examples of how the above summary route would be configured on ethernet0 in both RIPv2 and EIGRP.

R1(config-if)#ip summary-address rip 100.16.0.0 255.252.0.0

R1(config-if)#ip summary-address eigrp 100 100.16.0.0 255.252.0.0

The main difference between the two is that the EIGRP command must specify the AS number – thats what the “100″ is in the middle of the EIGRP command. Since RIPv2 does not use AS numbers, theres no additional value needed in the configuration.

For OSPF, the commands differ. If youre configuring inter-area route summarization, use the “area range” command. The number following “area” is the area containing the routes being summarized, not the area receiving the summary.

R1(config)#router ospf 1

R1(config-router)#area 1 range 100.16.0.0 255.252.0.0

If you are summarizing routes that are being redistributed into OSPF, use the summary-address command under the OSPF routing process on the ASBR.

R1(config)#router ospf 1

R1(config-router)#summary-address 100.16.0.0 255.252.0.0

I speak from experience when I tell you that practice makes perfect on the BSCI exam, especially with binary and summarization questions. The great thing about these questions is that there are no grey areas with these questions – you either know how to do it or you dont. And with practice and an eye for detail, you can master these skills, pass the exam, and become a CCNP. Heres to your success on these tough Cisco certification exams!

Add to | DiggThis | Yahoo! My Web

Technorati:

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of FREE CCNA and CCNP tutorials and daily exam questions, as well as The Ultimate CCNA and CCNP Study Packages.

For a FREE copy of his latest e-books, “How To Pass The CCNA” or “How To Pass The CCNP”, and for free daily exam question, visit the website and download your copies!

ISIS and OSPF are both link-state protocols, but ISIS works quite differently from OSPF. You must master these details in order to earn your CCNP.

One of the major differences between OSPF and ISIS will be evident to you when you first begin your BSCI exam studies, and that is the terminology. ISIS uses terms that no other protocol youve studied to date uses, and learning these new terms is the first step to BSCI and CCNP exam success.

First off, what does “IS” stand for in “ISIS”? It stands for “Intermediate System”, which sounds like a group of routers. As opposed to Autonomous Systems, which are logical groups of routers, an Intermediate System is simply a single router. Thats it.

Youll also become familiar with End Systems, referred to in ISIS as an “ES”. The End System is simply an end host.

ISIS and OSPF both use the concept of areas, but ISIS takes a different approach to this concept. ISIS routers use three different types of routing levels, according to the area a router has been placed in. Level 2 routers are connected only to the backbone and serve as a transit device between non-backbone areas. Level 1 routers are totally internal to a non-backbone area.

ISIS uses both Level-1 and Level-2 Hellos, meaning that the two types of routers just mentioned cannot form an adjacency. Luckily for us, there is a middle ground, and that is the Level 1-2 router. These routers connect non-backbone areas to backbone areas. L1-L2 routers keep two separate routing tables, one for L1 routing and another for L2 routing. This is the default setting for a Cisco router, and L1-L2 routers can form adjacencies with both L1 and L2 routers.

Part of the challenge of learning ISIS is getting used to the differences between ISIS and OSPF. Keep studying the terminology, master one concept at a time, and soon youll be a master of ISIS and a CCNP to boot!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of FREE CCNA and CCNP tutorials and daily exam questions, as well as The Ultimate CCNA and CCNP Study Packages.

For a FREE copy of his latest e-books, “How To Pass The CCNA” or “How To Pass The CCNP”, and for free daily exam question, visit the website and download your copies!

One major difference is the way the two protocols handle hello packets.

Hello packets are imperative to keeping OSPF and ISIS adjacencies alive. Since they are both link-state protocols, neither of them will send updates at any specified time. Hello packets are the only method by which routers running OSPF and ISIS can see that a neighboring router is still available.

OSPF gives us some great options when it comes to keeping routing table size down via the use of stub and total stub areas, but to OSPF, a hello packet is a hello packet. ISIS routers are capable of sending two different types of hellos – Level 1 and Level 2.

ISIS routers are classified as Level 1 (L1), Level 2 (L2), and Level 1-2 (L1-L2). By default, Cisco routers are L1-L2 routers; this means that every ISIS-enabled interface will send out both L1 and L2 hellos.

If one of the interfaces is forming only an L1 or L2 adjacency, theres no reason to send out hellos for the other adjacency type. For example, if R1 is forming an L1 adjacency with R2 via its ethernet0 interface, there is no reason to allow the router to transmit L2 hellos. To hardcode a router interface to send only L1 or L2 hellos, use the isis circuit-type command.

R1(config)#interface ethernet0

R1(config-if)#isis circuit-type level-1

Note: To configure this interface to send only L2 hellos, the full command is “isis circuit-type level-2-only”, not just “level-2″.

This configuration would prevent L2 hellos from being transmitted out ethernet0. While this does save router resources and prevents unnecessary bandwidth usage, there is also no way an L2 adjacency can be formed – so double-check your network topology before using this command!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of FREE CCNA and CCNP tutorials and daily exam questions, as well as The Ultimate CCNA and CCNP Study Packages.

For a FREE copy of his latest e-books, “How To Pass The CCNA” or “How To Pass The CCNP”, and for free daily exam question, visit the website and download your copies!

BGP is totally different from any protocol you learned to earn your CCNA certification, and one of the differences is that BGP uses path attributes to favor one path over another when multiple paths to or from a destination exist.

Notice I said “to or from”. In earlier free BGP tutorials, I discussed the BGP attributes “weight” and “local preference”. These attributes are used to favor one path to a destination over another; for example, if BGP AS 100 has two paths to a destination in AS 200, these two attributes can be set in AS 100 to favor one path over another. But what if AS 100 wants to inform the routers in AS 200 as to which path it should use to reach a given destination in AS 100?

Thats where the BGP attribute “Multi-Exit Discriminator”, or MED, comes in. The MED value can be set in AS 100 to tell AS 200 which path it should use to reach a given network in AS 100.

As with many BGP attributes, the MED can be set with a route-map. What you need to watch is that there is no “set med” value in route maps. To change the MED of a path, you need to change the metric of that path. Lets say that there are two entry paths for AS 200 to use to reach destinations in AS 100. You want AS 200 to use the 100.1.1.0/24 path over the 100.2.2.0/24 path. First, identify the two paths with two separate ACLs.

R1(config)#access-list 22 permit 100.1.1.0 0.0.0.255

R1(config)#access-list 23 permit 100.2.2.0 0.0.0.255

Next, write a route-map that assigns a lower metric to the more-desirable path.

R1(config)#route-map PREFER_PATH permit 10

R1(config-route-map)#match ip address 22

R1(config-route-map)#set metric 100

R1(config-route-map)#route-map PREFER_PATH permit 20

R1(config-route-map)#match ip address 23

R1(config-route-map)#set metric 250

Finally, apply the route-map to the neighbor or neighbors.

R1(config-route-map)#router bgp 100

R1(config-router)#neighbor 22.2.2.2 route-map PREFER_PATH out

The key points to keep in mind is that while many BGP attributes prefer a higher value, the MED is basically an external metric – and a lower metric is preferred, just as with the protocols youve already studied to earn your CCNA certification.

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of FREE CCNA and CCNP tutorials and daily exam questions, as well as The Ultimate CCNA and CCNP Study Packages.

For a FREE copy of his latest e-books, “How To Pass The CCNA” or “How To Pass The CCNP”, and for free daily exam question, visit the website and download your copies!